Mimaki JFX220-2515 UV Flatbed Printer
Expand rigid-media production with a large print bed, simplified media setup, and vivid UV printing. Print boards and panels up to 98.4 × 59.1 inches and up to 4 inches thick, held in place by ANCHOR TECHNOLOGY suction.

- Print area, in
- 98.4 × 59.1
- Max media thickness
- 4 inches in
- LD4 head gap
- 20 millimeters mm
- Layered ink
- 5 millimeters mm


Media Hold-Down
Simplify Setup with ANCHOR TECHNOLOGY
A newly developed suction table focuses vacuum on the area where your media sits, so you can skip masking off the rest of the bed.
- Targeted suction. The table secures the area under the substrate rather than relying on you to block unused holes.
- No masking for setup. Mimaki says this cuts print preparation time between jobs.
- Test warped media first. Sheets with extreme warping or lifting may not hold securely, so run a hold-down test before printing.
Application Gallery
Build a Broader Application Mix
From counter displays and event signage to interior décor and skateboard decks, a 98.4 × 59.1-inch bed covers full boards and batches of smaller pieces.

Event and venue signage 
Counter displays 
Yard signs 
Interior door décor 
Skateboard decks
UV-Curable Ink
Choose Color and Ink Effects for the Job
Set the JFX220-2515 up for speed, for white and clear effects, or for fluorescent color. Available colors depend on the configuration you select.


Texture and Depth
Texture and Uneven Surfaces
Two separate capabilities: LD4 mode prints across a wider gap to surfaces that aren't perfectly flat, and layered ink builds raised texture on top of the print.
LD4 print distance
Measured from the printhead to the printing surface. This is not the media thickness limit.
Layered ink
Build ink up for dimensional effects, art panels, and Braille signage.
Maximum media thickness is a separate limit: 101.6 mm (4 in). LD4 sets how far the head can be from the surface it prints on.

Technical Specifications
Machine Details and Installation
A full-size flatbed needs a planned space. Use the footprint and weight below as a starting point, and talk with Amcad about access, power, and working room around the bed.



| Max printable area | 2,500 × 1,500 mm (98.4 × 59.1 in) |
|---|---|
| Suction (hold-down) area | Up to 2,500 × 1,930 mm (98.4 × 76.0 in), 25 mm (1 in) hole pitch |
| Max media thickness | 101.6 mm (4.0 in) |
| Media load | Under 50 kg/m², evenly distributed (no concentrated loads) |
| Print resolution | X: 600, 900, or 1,200 dpi Y: 300, 600, or 1,200 dpi |
| Ink | ELH-100 hard UV ELS-120 flexible UV EFS-150 fluorescent pink and yellow PR-200 primer |
| Interface | Gigabit Ethernet (1000BASE-T) |
| Dimensions (W × D × H) | 4,400 × 2,520 × 1,490 mm (173.2 × 99.2 × 58.7 in) |
| Machine weight | 920 kg (2,028.3 lb) |
Specifications are from Mimaki and may change without notice. Available ink colors depend on the selected configuration. Feet values are converted from inches and rounded.
Common Questions
Questions About Large-Format UV Printing
Why is the hold-down area larger than the print area?
The printer prints up to 2,500 × 1,500 mm (98.4 × 59.1 in), while the suction table covers up to 2,500 × 1,930 mm (98.4 × 76.0 in). Plan artwork within the printable area. The larger suction area helps hold the media you place on the bed.
How thick can my media be?
Up to 101.6 mm (4 in). Media load should stay under 50 kg/m² and be evenly distributed, without concentrated loads.
Which ink should I choose?
Choose ELH-100 hard or ELS-120 flexible UV ink to suit your materials, then pick a configuration: dual CMYK for faster work without white or clear, CMYK with white, clear, and primer for colored and transparent media, or fluorescent pink and yellow for neon-style color. Amcad can help you test on your substrates.
How does ANCHOR TECHNOLOGY work?
The suction table focuses vacuum on the area where your media sits, so you don't need to mask the rest of the bed. Media with extreme warping or lifting may not hold securely, so test hold-down before printing.
Can it print dimensional effects?
Yes. Layered ink can reach 5 mm for raised texture, art panels, and Braille signage. Separately, LD4 mode prints with up to 20 mm between the printhead and the printing surface for uneven surfaces.

RIP and Workflow Software
RasterLink8 for Flatbed Production
RasterLink8 brings print preparation and production management into the workflow. Explore supported fluorescent color tools, job management, and color-matching functions for your printer and ink configuration.
Fluorescent color
Fluorescent color collection workflows for the JFX220 with EFS-150 ink.
Job management
Job management, scheduling, and template-based job creation.
Color emulation
Printer-to-printer color matching. Requires a colorimeter and peripheral equipment sold separately.
Feature support depends on printer, software version, ink configuration, and optional equipment.
OEM Parts Reference
Find the Right Mimaki Part
Use the Amcad parts reference lookup to identify Mimaki OEM part numbers by machine model, assembly area, or component, then browse matching parts collections.
Talk With Amcad
Discuss Your Next Flatbed Project
Send us your boards and panels for sample printing, see the JFX220-2515 in action, or talk through ink, hold-down, and installation with the Amcad team.
Bookmarks
Bookmarks is empty.