
Mimaki TxF330-800 DTF Printer
Bring vivid apparel graphics and dependable film production into your print shop with the Mimaki TxF330-800. This 31.5-inch direct-to-film platform prints full-color transfers with a white underbase, ready for powder, curing, and heat pressing onto garments and accessories.

- Max print width
- 31.5 in
- PHT50 ink setups
- 2
- Max white ink
- 4 L
- Film roll support
- 100 m
How DTF Production Works
DTF Printing for Custom Apparel
Direct-to-film printing separates artwork from the garment. Print once onto transfer film, finish the transfer, and press it onto tees, hoodies, totes, and more.
-
Prepare the design
Lay out artwork in your RIP software, plan the white underbase, and nest designs to make the most of each roll.
-
Print onto film
The TxF330-800 prints color and white PHT50 ink onto transfer film up to 31.5 inches wide.
-
Powder and cure
Adhesive powder is applied to the wet print, then cured so the transfer is ready to handle, store, or press.
-
Heat press
Press the cured transfer onto the garment or accessory, then peel the film to reveal the finished graphic.
Powder application, curing, and heat pressing are handled by separate post-processing equipment. Plan the printer and finishing equipment together as one complete production workflow, and talk with Amcad about sizing that line for your volume.



PHT50 Pigment Ink
Choose Your Color Configuration
The TxF330-800 runs Mimaki PHT50 heat transfer pigment ink in one of two configurations. Compare them below and pick the setup that matches the work you sell most.


Unattended Production
Keep Longer Jobs Moving
Built to reduce stops during long transfer runs and overnight batches.
White ink capacity
Load up to 4 liters of white, the color DTF jobs use most, using 500 ml white packs.
100-meter film rolls
Supports 100 m (about 328 ft) film rolls up to 45 kg (99 lb) for long runs between roll changes.
Automatic cartridge switching
When one cartridge empties, the printer moves to the next, and empty packs can be swapped while printing continues.
White ink circulation
A circulation system keeps white ink moving to help stabilize jetting and reduce ink used during nozzle cleaning.
Nozzle check and recovery
A sensor detects missing nozzles and triggers cleaning. If a nozzle can't be recovered, substitute nozzles can print in its place, depending on the position and number of missing nozzles.
Feature overview based on Mimaki specifications. Not live machine data.


Application Gallery
See the Applications
From one-off portrait tees to full team orders, DTF transfers cover a wide range of garments and accessories from one film workflow.

Hoodie back and sleeve graphics 
Matching team jerseys 
Full-color tote bag artwork 
Photo portrait T-shirts 
Cap graphic 
Graffiti hoodie and cap set
Technical Specifications
Machine Specifications
| Maximum print width | 800 mm (31.5 in) |
|---|---|
| Maximum media width | 810 mm (31.9 in) |
| Print resolution | X: 600 or 1,200 dpi Y: 600, 900, or 1,200 dpi |
| Ink | PHT50 heat transfer pigment ink CMYK + White, or CMYK + Sky Blue + Pale Pink + White |
| Ink pack capacity | Color: 600 ml per pack White: 500 ml per pack |
| Maximum roll weight | 45 kg (99 lb) |
| Dimensions (W × D × H) | 2,084 × 700 × 1,389 mm (82.0 × 27.6 × 54.7 in) |
| Machine weight | 161 kg (355 lb) |
| Interfaces | Gigabit Ethernet (1000BASE-T) USB 2.0 Hi-Speed |
Specifications are from Mimaki and may change without notice. Inch and pound values are converted from metric and rounded.
Common Questions
Questions About Your DTF Workflow
What is the difference between print width and film width?
The TxF330-800 prints up to 800 mm (31.5 in) wide and accepts media up to 810 mm (31.9 in) wide. The extra width is media margin, so plan transfer layouts within the 31.5-inch printable area.
Which color configuration should I choose?
CMYK + White suits shops that prioritize output volume and bold graphics. CMYK + Sky Blue + Pale Pink + White expands color for vivid blues, greens, pinks, and smoother skin tones in photo work. The two setups don't run at identical speeds, so Amcad can help you weigh color range against throughput for your order mix.
What does the printer actually produce?
The TxF330-800 prints full-color designs with a white layer onto transfer film. After powder application and curing, those transfers are heat pressed onto garments and accessories such as T-shirts, hoodies, jerseys, totes, and caps.
What equipment is used after printing?
A complete DTF line typically adds a powder application and curing step after the printer, followed by a heat press to transfer the design onto the item. Amcad can help you plan post-processing equipment that fits your space and production goals.

RIP and Workflow Software
RasterLink and Your DTF Workflow
Prepare print data and coordinate your DTF production workflow with Mimaki RasterLink software. Good transfers start in the RIP, where artwork is color-managed, white layers are planned under the design, and jobs are laid out across the film.
RasterLink8 is Mimaki's current workflow software. Ask Amcad which RasterLink configuration fits your TxF330-800 installation. We'll confirm version, licensing, and compatibility for your setup, along with the other workflow tools available for your shop.
OEM Parts Reference
Find the Right Mimaki Part
Use the Amcad parts reference lookup to identify Mimaki OEM part numbers by machine model, assembly area, or component, then browse matching parts collections.
Talk With Amcad
Plan Your Next Apparel Workflow
See the TxF330-800 in action, request print samples, or talk through ink configuration, finishing equipment, and software with the Amcad team.
Bookmarks
Bookmarks is empty.